MAXTER INJECTORS USEWAY
How to compress Animal injectors
Click Download useway (p.09-11)
insert the normal injector with 20-30 cc capacity behind the animal injector and secure the space for drug injection
-> inject drug with the small injector and insert the injector needle for compression
-> draw out the animal injector in the state of strong compression by the normal injector.
In order to make compression stronger, it is effective to compress using a needle as thick as blow-gun one.
When the rubber bucking will not move, it is okay to push it with wire, etc.
The as compression type is completed by inserting the injector needle at the lighter gas cask into the animal injector,
inject the fluid gas and then draw out the animal injector.
In case of gas injection, it is effective using the rubber for bicycle to prevent leakage.
The state of compression is maintained about 40-50 minutes.
In case of over 3cc drug injection, it is quick and powerful to use the gas type.
How to load
1. Slip the safety up front -> lift up finger stop -> step on the pedal -> pull the trigger -> keep the launch position
2. Insert animal syringe from the gun point. (Note: One of the three wings on the syringe has to face down on the gun point. This means when looking at gunbarrel from behind, syringe wing should not be seen then push it all the way back to the gunbarrel.
3. Cover up front part of syringe arrow with a cloth then pull. When you hear "click" sound from the trigger assembly, it means loaded correctly.
1. Slip the safety up front -> lift up finger stop -> step on the pedal -> pull the trigger -> keep the launch position
2. Insert animal syringe from the gun point. (Note: One of the three wings on the syringe has to face down on the gun point. This means when looking at gunbarrel from behind, syringe wing should not be seen then push it all the way back to the gunbarrel.
3. Cover up front part of syringe arrow with a cloth then pull. When you hear "click" sound from the trigger assembly, it means loaded correctly.
How to aim
1. When in launch preparation position, moving gap start point is going to be standard then aline the end of gunbarrel and the target.
2. Projected syringe front and target should be lined up. Depend on the distance, aim it up and down. (Distance adjustment and up, down, right, left adjustment can be different by each individual)
3. Take advantage of animal syringe which tend to fly straight.
4. Syringe arrow position should be same as illustrated on right for higher accuracy.
How to undo the launch position
To undo the launch position, hold the handle with one hand and with the other hand, pull the trigger.
1. When in launch preparation position, moving gap start point is going to be standard then aline the end of gunbarrel and the target.
2. Projected syringe front and target should be lined up. Depend on the distance, aim it up and down. (Distance adjustment and up, down, right, left adjustment can be different by each individual)
3. Take advantage of animal syringe which tend to fly straight.
4. Syringe arrow position should be same as illustrated on right for higher accuracy.
How to undo the launch position
To undo the launch position, hold the handle with one hand and with the other hand, pull the trigger.
Precaution
Do NOT Dry Fire 1. When animal syringe is fired without being loaded, percussion break away from gunbarrel. Please double check.
2. Also, when firing, the hand that holds the gunbarrel must not block the percussion route.
3. After 10 to 20 firing, apply lubricant inside the gunbarrel. (For the lubricant, use water wax used for cars.)
4. Before loading syringe arrow, make sure backside cork is completely locked. If this step is neglected, shot will be out of its
Do NOT Dry Fire 1. When animal syringe is fired without being loaded, percussion break away from gunbarrel. Please double check.
2. Also, when firing, the hand that holds the gunbarrel must not block the percussion route.
3. After 10 to 20 firing, apply lubricant inside the gunbarrel. (For the lubricant, use water wax used for cars.)
4. Before loading syringe arrow, make sure backside cork is completely locked. If this step is neglected, shot will be out of its
Syringe Usage
※Both the gas fill system and the air compression system open the top of the syringe and apply the lid to the cap and coverthe lid. Move the needle to the syringe, lock the back, and use it.
Gas compression system
1.The gas fiiled method inserts of one syringe to the compression chamber through a sigle injection.
2.Charge it with liquid gas as shown in figure left. When the gas is visually checked at the bottom of the syringe, it is kept for two hours. Advantage: More than twice as much momentum as air compression.
Large doses of injections are injected momentarily and can be seen and fired with compression.
Air compression system
1. Attach the 30cc syringe to rear of the syringe and pump the pump more than 7times to compress the air.
2. Make sure that the water is immersed in the glass and the release.
3.The compressed time is used for 24 hours and a gas is not available.
How to use syringe
1. When the rubber part of syringe is not inserted, push down a little.
2. Adjust the rubber up and down with big syringe to make room to insert drug
3. Insert drug
4. Spin syringe niddle (silicon rubber stopper) strongly to insert.
5. Push drug syringe from behind with the big syringe strongly then pull it off
2. Adjust the rubber up and down with big syringe to make room to insert drug
3. Insert drug
4. Spin syringe niddle (silicon rubber stopper) strongly to insert.
5. Push drug syringe from behind with the big syringe strongly then pull it off
useway syringe anesthesia Watch youtube
https://youtu.be/bXYsVABYfeg
Shooting the rope reel
Before shooting, undo the rope 40 to 50 meter.
How to change the rope
1. Measure exactly half from each side to mark center. Use 'R' to insert ball then tie
2. Each side balance is correlated with accuracy. Try practice shooting several times and make adjustment
3. Loosen the screw on the burst -> remove the gunbarrel -> cut the latex rope to insert onto fixed ring -> once the rope is inserted on the fixed ring, adjust the strength of the rope
2. Each side balance is correlated with accuracy. Try practice shooting several times and make adjustment
3. Loosen the screw on the burst -> remove the gunbarrel -> cut the latex rope to insert onto fixed ring -> once the rope is inserted on the fixed ring, adjust the strength of the rope
댓글 없음:
댓글 쓰기